Ford Ecosport P2007: Causes + Diagnosis

by

P0118 Ford Ecosport

P2007 Definition: IMRC – Stuck Closed – Bank 2

Ford Ecosport P2007 Meaning

Here is the definition of P2007.  Understanding it can help make diagnosis easier.

IMRC Control

Your Ford Ecosport’s throttle body allows air into the intake manifold.  Once the air makes its way through the intake, the IMRC system fine-tunes the airflow for each particular intake runner.  This action creates a swirling effect that allows for more efficient combustion, which increases fuel economy and decreases emissions.

The IMRC is controlled by your Ecosport’s powertrain control module (PCM).  It can use either engine vacuum or an electric motor to operate the system (depending on model year and engine type). However, the vacuum-operated version does seem to be more prevalent.

Stuck Closed

The IMRC is stuck closed and can no longer fine-tune the air.  If it is stuck closed, it can limit air intake at higher RPMs.  This may cause some unwanted effects (covered below). 

Bank 2

Each of your Ecosport’s cylinder heads is considered to be a “Bank.”  Bank 2 is the cylinder head with the second cylinder.  Since P2007 deals with bank 2, there’s a bank one.  You’ll need to determine which side of your engine has cylinder two.

If you also got P2006 when scanning your Ecosport (same problem, only bank one), you should start by looking for a vacuum leak.  It would be very unlikely that they’d both go out at the same time.

P2007 Symptoms:  Ford Ecosport

Here are the most common symptoms associated with P2007:

  • The air-fuel mixture will be richer, at higher RPM’s
  • Decreased fuel economy
  • Surging Engine/Stalling

Ford Ecosport P2007: Causes + Diagnosis

Ecosport P2007 Diagnosis

Here are things most likely to cause P2007 in your Ecosport, as well as a good order of diagnostic operations:

IMRC Wiring

The wiring harness going to the IMRC and the pigtail that connects to it can cause P2007.  If the IMRC actuator no longer has power, then it can’t operate the butterfly valves.  This leaves the system “stuck closed”.

Check the wiring harness around your Ecosport’s IMRC to ensure that it hasn’t been rubbed against anything and damaged.  If it has, you’re going to need to replace or repair the wiring harness.

Make sure that the harness has the proper voltage (or voltage going to it at all).  Verify that the ground is good.

Restricted Vacuum Lines (Vacuum Operated IMRC Only)

Most IMRC systems are vacuum controlled.  Check the vacuum lines going to it to see if they are restricted or damaged in any way.  If there is a leak, you’ll need to replace the lines.

If your Ecosport has a vacuum-operated IMRC, you can control the butterfly valves with a vacuum pump (like a Mityvac).  Use a vacuum pump to verify that the IMRC actuator can still operate the butterflies.  If it does operate them, you know that either there’s not enough vacuum getting to the IMRC actuator for it to be effective, or something is not commanding it to turn on.

If the vacuum pump does not operate the IMRC actuator, it’s likely bad and causing P2007.

Intake Manifold and Linkage

With your Ecosport’s IMRC actuator disconnected, you can operate the linkage by hand.  It shouldn’t give any resistance when moving it.  If it does, then it’s binding in the intake.  This can happen for a few reasons:

  • Carbon build-up
  • Intake manifold improperly torqued
  • Bent or loose IMRC butterfly valves

If the butterfly valves open and close with no resistance, you can rule out any issue with the intake, which either leaves the IMRC actuator or something causing it not to command open or closed.

If they do not freely move, there is either a carbon buildup or the butterfly valves have come loose.

Bad MAP/MAF Sensor

The PCM uses data from your Ecosport’s manifold absolute pressure (MAP) or mass airflow (MAP) sensors to verify that the butterfly valves have opened as much as they should have (or at all).  

If it does not see the data that it should, that can be enough to throw P2007.

Bad IMRC Actuator

Replacing the IMRC actuator is perhaps the most common fix for P2007.  In the previous step, you checked all of the wiring going to it and ensured that it was good.  So, at this point, it’s likely to be the IMRC actuator causing P2007.

Conclusion

As you can see, there are a lot of potential causes of P2007 in the Ford Ecosport. Take your time, use the process of elimination, and you should have the code cleared in no time.  Good luck!